Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
Test principle and precautions of fabric hydrostatic pressure tester
The fabric hydrostatic pressure tester test device is composed of stainless steel materials, and provides a horizontal test platform. There is a 100cm2 test groove on the platform. The outer circumference of the test groove has a rubber O-ring seal, and the pressure sensor is installed in the test hole. There is also a leveling bubble on the platform, which can control the levelness of the platform by rotating the feet. Above the platform is a fixing frame, which can make the cloth pressing triangular cover fit the test groove, and the inner diameter area of the pressing cloth triangular cover is 100cm2. The cloth pressing triangular cover is driven by the rotating handle and can move up and down to place and clamp the cloth sample for testing. Below the platform is the hydrostatic supply part, which is composed of a water storage tank, an electromagnetic pump, a conduit, a water level inspection, a water discharge valve, and a calibration interface. The structure diagram of the test device is as follows: Main parameters: 1. Test pressure: 0-5000mbar; 2. Pressure accuracy:±1mbar; 3. Resolution: 0.1mbar; 4. Ascent rate: 1-300mbar/min; 5. Test area: 100cm2 (optional 10cm2, 19.63cm2, 26cm2, 28cm2); 6. Sample thickness: no more than 5mm; 7. Compressed air requirements: 6-8bar (clean and dry air). Test Principle: Apply an increasing (dynamic test) or consistent (static test) water pressure to the sample until water seeps out from three different locations on the sample. After testing at least 3 samples, measure and calculate the average maximum water pressure of the fabric (measured in mBar or cmH2O). This value is the water repellency of the sample. The specific method is that the sample is fixed on the test area of the standard area, and the air compressor adds 0-5bar air into a water tank filled with distilled water, and applies a certain pressure of water to the sample. It can be tested by two methods: dynamic or static: (1) Dynamic method: determine the hydrostatic resistance of the sample by testing the pressure when a fixed number of water droplets seep out from the side of the sample that is not in contact with water at a certain pressure increase rate pressure performance. (2) Static method: The hydrostatic pressure resistance performance of the material is determined by testing the water seepage of the sample after maintaining the pressure for a certain period of time under a certain hydrostatic pressure. Matters needing attention: 1. The sample should be placed horizontally without bulging; 2. The area above or below the fabric subjected to continuous rising water pressure is 100cm2; 3. During the test, the clamping device should not leak; 4. The sample is clamped There will be no slippage in the device; 5. Minimize the possibility of water seepage of the sample at the edge of the clamping device.
Service-based companies as GESTER International Co.,Limited are increasingly becoming more popular internationally.
Dazzle your next event with tensile tester manufacturers textile testing equipment and to buy best product， only trust GESTER International Co.,Limited.
By balancing the efficiencies of new technologies with the personal touch of highly trained and motivated professionals, GESTER International Co.,Limited is able to deliver solutions and services that exceed our customers’ expectations. We thereby earn their loyalty.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Quick links