Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
What are the testing methods and instruments for the burning characteristics of textiles?
1. Fabric burning performance test: It is mainly used to test the burning breadth (carbonized area and damage length), continuous burning time and smoldering time of the sample. According to the relative position of the sample and the flame, it can be divided into vertical burning method, horizontal burning method and 45 degree burning test method. Test principle: The vertical combustion method is to set a certain size sample perpendicular to the specified combustion test box and ignite it with a specified fire source for 12 seconds. After the fire source is removed, the continuous burning time and smoldering time of the sample are measured, and the smoldering time is measured after stopping Damage length. The test principles of the horizontal test method and the 45-degree combustion test method are the same as those of the vertical test, and the ignition time is different. Compliant with standards: ASTM D6413-99, DOC-FF 3/71, CALIF TB-117, GB/T 5455, CPAI-84; ISO 3795, FMVSS 302, DIN 75200, SAE J369, ASTM D5132, JIS D1201, AU169, FZ /T 01028; ASTM D1230, FTMS 191-5908, CFR 16 Part1610, CAL IF TB117, NFPA702, GB/T 14644 2. Limiting oxygen index test: Limiting oxygen index: Under the specified test conditions, the material is kept in a burning state. The minimum concentration of oxygen in the mixed gas of nitrogen and oxygen. Test principle: Fix a sample vertically in a transparent combustion tube of upwardly flowing oxygen and nitrogen mixture, ignite the top of the sample, and observe the combustion characteristics of the sample, and compare the continuous burning time or the burning length of the sample with the Compared with the established criterion, the minimum value of oxygen concentration is estimated through a series of tests under different oxygen concentrations. Compliance with standards: ISO 4589-2, ASTM D2863, GB/T2406, GB/T5454 3. Smoke density test: Smoke density refers to the measurement of the amount of smoke produced by a material under specified test conditions, which reflects the degree of opacity of smoke. The higher the smoke density of the material, the more unfavorable it is for evacuation and fire fighting during a fire. Test range: The plastic burning smoke density tester is for the smoke density test of the sample from the sheet-shaped material, composite material, or composite parts with a thickness of no more than 25mm. This test instrument is not only suitable for all plastics, but also for rubber, textile coverings, painted surfaces, wood and other materials. Test principle: Place the sample horizontally in the test box, and expose the upper surface of the sample to a heat radiation source with a constant irradiance within 50KW/m2. The generated smoke is collected in a test box equipped with a photometer. Measure the attenuation of the beam after passing through the smoke. Compliance with standards: GB8323.2-2008, ISO5659.2-2006. IV. Combustion oxygen consumption and heat release rate test: The heat release rate and total amount of the material when burned are the most important parameters in its combustion performance, which can be compared Accurate measurement of the heat release rate during material combustion is very important for predicting fire hazards. At present, the main secondary test method is cone calorimetry. Test principle: The sample is burned under the heat radiation of the cone electric heater. The flame consumes a certain concentration of oxygen in the air and releases a certain heat of combustion. The instrument can measure the rate of heat release, the amount of CO and CO2 produced, the rate of oxygen consumption, and the amount of smoke released. Compliant with standards: ISO 5660, ASTM E1354, ASTM E1474, ASTM E1470, ASTM F1550, ASTM D6113, NFPA 264, CAN ULC135, BS 476. More about the combustion tester: http://www.ranshaoceshi.com/
tensile tester manufacturers textile testing equipment processes have been widely used to produce tensile tester manufacturers such as tensile tester manufacturers, tensile tester manufacturers, and tensile tester manufacturers etc.
To live healthy, you need to eat healthy; to eat healthy, you need to think healthy; to think healthy, you need to read health; to read healthy, you need to follow GESTER Instruments.
tensile tester manufacturers textile testing equipment with tensile tester manufacturers are used extensively in tensile tester manufacturers.
When selecting the best products for customers, we considered not only the textile testing equipment, but also the tensile tester manufacturers.
Ball Burst Method (ASTM D3787): Steel ball penetration for textiles/films using testers like GT-C02-2.
Hydraulic Method (ISO 13938.1): Fluid pressure on rubber diaphragm for industrial fabrics via GT-C12A.
Pneumatic Method (ISO 13938.2): Compressed air for breathable materials tested with GT-C12B.
Results are influenced by raw materials, yarn properties,
Quick links