Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
Analysis of test method for resistance to draw of cigarettes
Cigarettes are a common type of consumer product in daily life. The question of whether cigarettes are good or bad and whether they should be banned will not be discussed in this article. Scope: This standard specifies the method for determining the draw resistance of cigarettes. This standard applies to all kinds of cigarettes. Normative references: The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties using this standard should explore the possibility of using the latest edition of the following standards. GB/T5606.1-1996 Cigarette Sampling GB/T16447-1996 Tobacco and Tobacco Products Conditioning and Atmospheric Environment Determination Principle: Under standard conditions, when a steady airflow of 17.5mL/s flows through the cigarette sample When , the pressure difference between the two ends of the sample is the suction resistance of the sample. Instruments and equipment: 1. Instruments for measuring cigarette resistance should meet the following requirements:— Air flow: 17.5mL/s;— Probe: It can seal and measure the sample. During the measurement, the outlet end of the sample is inserted into the probe by 9mm, and there should be a layer of film in the test head. During the measurement, the film completely wraps the sample in the probe, and there should be no air between the wrapped part of the film and the sample;— Range->5kPa; resolution: 10Pa;— Measured value display accuracy: 1OPa, 2. A set of standard bars: The difference between the standard values of two standard bars is not less than 1kPa; the accuracy (relative error) of the standard bars is 1%. Measurement steps: Adjust the sample according to GB/T 16447, and Tested under corresponding environmental conditions. 1. Turn on the power of the instrument and preheat to make it stable. 2. Connect the air circuit. 3. Use the high and low standard rods to calibrate the instrument respectively, so that the relative error between the displayed value of the instrument and the standard value of the standard rod does not exceed 1%. 4. Insert the outlet end of the sample into the probe of the instrument, and the insertion depth is 9mm , so that the film wraps the sample inside the probe tightly. 5. The resistance reading should be obtained within 2-3s after the sample is inserted into the instrument
GESTER International Co.,Limited is willing to push up our sleeves and wade into unknown territory with equal parts fearlessness and optimism.
Dedicated to bringing you professional textile testing equipment solutions and related products – from tensile tester manufacturers to tensile tester manufacturers, GESTER International Co.,Limited is your textile testing equipment helper. Visit us at GESTER Instruments.
For more textile testing equipment tensile tester manufacturers reviews, tips and advice on choosing a washer and dryer for you and your family, please visit GESTER Instruments,where you can also choose the you are looking for.
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
Ball Burst Method (ASTM D3787): Steel ball penetration for textiles/films using testers like GT-C02-2.
Hydraulic Method (ISO 13938.1): Fluid pressure on rubber diaphragm for industrial fabrics via GT-C12A.
Pneumatic Method (ISO 13938.2): Compressed air for breathable materials tested with GT-C12B.
Results are influenced by raw materials, yarn properties,
Quick links