Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
Helmet impact resistance piercing machine instructions
Safety helmet impact resistance puncture tester operation steps are as follows: a. Safety helmet impact resistance puncture tester test preparation work: 1, the pretreatment temperature treatment: the helmet on 50 ℃ & plusmn; 2℃、- 10℃± 2 ℃ or - 20℃± 2 ℃ temperature control box placed 3 h. 2, ultraviolet irradiation pretreatment: use A standard in the first, and A helmet on the ultraviolet light irradiation in 400 h & plusmn; After 4 h, take out in a laboratory environment, put 4 h. 3, immersion treatment: put a helmet on temperature is 20 ℃ & plusmn; 2 ℃ fresh tap water tank, completely soaked for 3 h. 4, according to the safety helmet worn height to choose the appropriate headform ( Pay attention to in the replacement head must shut off the power switch) ; Normal wear safety helmet on head, ensure the cap band contact with the head of natural wear state and stable. Second, helmet impact resistance puncture tester shock absorption performance operation step 1, open the power switch of the instrument. 2, will be prepared a safety helmet, wear a head model, the door is closed test. Then click & other; Reset & throughout; Button to remove system zero value. 3, press & other; And off & throughout; Key, electromagnetic suction device work, put the drop hammer impact on plane electromagnetic device under the plane, is sucked impact hammer. 4, with a height of test impact hammer scale the distance from the bottom to crown, if did not meet the requirements of 1000 mm distance, through panel & other Rose & ndash; Stop & ndash; Drop & throughout; Twist the switch fine-tuning height, make it satisfy the requirement of the standard height. ( The distance between the height of drop hammer test rod telescopic rod up and down to 1000 mm) 5, press & other; Release & throughout; Key, electromagnetic suction device to stop working, the impact hammer quickly free fall on the top of the helmet, at the same time, the impact value shows and latches. Foot switch = off, can also be hand hammer, stepping on the pedal switch on and off the action! 6, record the impact as the numerical value display helmet impact resistance value, the door is open the test, take out the helmets and the impact hammer. 7, a test is completed, if you want to continue to repeat steps 2 to 6 for the next test. If you don't need to continue to test, please close the instrument power supply in a timely manner. Third, helmet impact resistance stab piercing machine durability performance operation step 1, open the power switch of the instrument. 2, will be prepared a safety helmet, wear a head model, the door is closed test. 3, press & other; And off & throughout; Key, electromagnetic suction device working, the puncture of drop hammer surface on the electromagnetic device under the plane, the puncture is sucked drop. 4, with the height of drop hammer test scale test puncture of the distance from the bottom to crown of drop hammer, if did not meet the requirements of 1000 mm distance, through panel & other Rose & ndash; Stop & ndash; Drop & throughout; Twist the switch fine-tuning height, make it satisfy the requirement of the standard height. ( The height of drop hammer test scale up and down the distance between the telescopic rod is 1000 mm) 5, press & other; Release & throughout; Buttons, electromagnetic suction device stops working, piercing drop quickly free fall on the top of the helmet, if the helmet is piercing drop penetration, the alarms drops of alarm, at the same time, the penetration on the operation panel light is lit up. 6, record test results, the door is open the test, remove the safety helmet and puncture drop hammer, a test is completed, if you want to continue to repeat 2 ~ 5 steps to test next time. If you don't need to continue to test, please close the instrument power supply in a timely manner. Above is the city jester testing equipment company brief GX - for you 7001 helmet impact resistance puncture tester instructions content knowledge. Thank you for your reading.
GESTER International Co.,Limited in the right situation can streamline the entire process, enabling your team to deliver higher quality work in a shorter amount of time.
GESTER International Co.,Limited will deliver superior returns to our shareholders by tirelessly pursuing new growth opportunities while continually improving our profitability, a socially responsible, ethical company that is watched and emulated as a model of success.
tensile tester manufacturers textile testing equipment will help keep your tensile tester manufacturers in a tensile tester manufacturers state.
There are multiple advantages of having a tensile tester manufacturers textile testing equipment from responsible drilling machine exporters such as GESTER International Co.,Limited, as they adhere to all the quality standards as you can list and supply all tensile tester manufacturers essential for the operation of the device without any difficulty.
Ball Burst Method (ASTM D3787): Steel ball penetration for textiles/films using testers like GT-C02-2.
Hydraulic Method (ISO 13938.1): Fluid pressure on rubber diaphragm for industrial fabrics via GT-C12A.
Pneumatic Method (ISO 13938.2): Compressed air for breathable materials tested with GT-C12B.
Results are influenced by raw materials, yarn properties,
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
1. ISO 5402-1: Specifies the flexometer method for testing leather flex resistance under repeated bending.
2. ISO 17694: Defines test methods for footwear upper and lining flex resistance, simulating real-world bending stress to assess long-term durability.
C
Quick links