Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
QB/T1811-1993 Leather Water Vapor Permeability Test
This standard specifies the test principles, test instruments, sample preparation, test procedures, calculations, and test reports for the water vapor permeability of leather under standard conditions. This standard applies to all leathers. Reference standard GB/T4689.1 leather laboratory sample location and mark GB/T4689.2 air conditioning test principle of the test piece for leather physical property testing Under certain temperature and humidity conditions, the leather test piece is fixed on the moving test bottle mouth , The test bottle is equipped with a solid desiccant. When the test bottle moves, the water vapor passes through the leather test piece and is absorbed by the solid desiccant. Weigh the test bottle within a specified time to confirm that the water vapor passes through the leather and is dried during this period of time. The weight absorbed by the agent. Sample 1. According to the No. 10 sample position specified in GB/T4689.1, remove the sample with a die. 2. Air-condition the sample according to the regulations of GB/T4689.2. Test step 1. Put half of the freshly dried silica gel (59.0±0.5) g into the test bottle, fix the sample on the bottle mouth with the use side inward, then fix the test bottle on the test bottle holder, and start the instrument. 2. Use a vernier caliper to measure the inner diameter of the second test bottle mouth in two mutually perpendicular directions, and mark the average diameter d. It is accurate to 0.1mm. 3. If necessary, it can be between the mouth of the bottle and the test piece. Add a washer or apply a layer of beeswax, or take other measures to prevent air leakage. 4. After the instrument has been rotated for 16 hours, stop it and remove the first test bottle. Put the other half of the freshly dried silica gel (59.0±0.5) g into the second test bottle, remove the sample from the first test bottle and fix it on the second test bottle as soon as possible, using the face inward. 5. Weigh the second test bottle, record the weighing time, and then fix the second test bottle on the instrument. 6. When the instrument rotates for 7 hours, stop it, remove the test bottle, weigh it, and record the weighing time. Test result Pu003d7369m/(d?×t) where: P——water vapor permeability, mg/(cm??h); m——the increased mass of the bottle after weighing twice, mg; d——bottle mouth The diameter, cm; t——the time between two weighings is small. Test report The test report includes the following content: a. The name and source of the tested sample; b. Each measurement result, the arithmetic average of multiple results; c. Save the sample and test conditions; d If it appears temporarily, it may produce experimental results. Factors affecting.
Many of us have heard about textile testing equipment and seen some of these units in operation in tensile tester manufacturers, tensile tester manufacturers and tensile tester manufacturers spaces.
tensile tester manufacturers are the in thing today. To buy a for yourself do visit GESTER International Co.,Limited at GESTER Instruments.
Like anything else in tensile tester manufacturers, there are a variety of choices and types to choose from, and each of them will affect your budget in some form. GESTER International Co.,Limited offers a range of quality at competitive prices.
Producing with varied technical skills, textile testing equipment can be used in a wide range of applications as tensile tester manufacturers.
Basically, you cannot have a tensile tester manufacturers without having the right textile testing equipment. Since you are going to use it regularly, be sure to invest in one that has a high quality.
Ball Burst Method (ASTM D3787): Steel ball penetration for textiles/films using testers like GT-C02-2.
Hydraulic Method (ISO 13938.1): Fluid pressure on rubber diaphragm for industrial fabrics via GT-C12A.
Pneumatic Method (ISO 13938.2): Compressed air for breathable materials tested with GT-C12B.
Results are influenced by raw materials, yarn properties,
1. ISO 5402-1: Specifies the flexometer method for testing leather flex resistance under repeated bending.
2. ISO 17694: Defines test methods for footwear upper and lining flex resistance, simulating real-world bending stress to assess long-term durability.
C
Quick links