Gester Instruments | Professional Textile Testing Equipment Manufacturers Since 1997
Test method for performance of filter gas mask canister
Subject content and scope of application This standard specifies the test methods for the anti-virus performance and physical properties of the filter gas mask canister (hereinafter referred to as the canister). This standard applies to the performance testing and evaluation of filter gas mask canisters: other related products can also be referred to. Reference standard GB 2890 General technical conditions for filter gas masks GB 7702.10 Determination of effective protection time of coal-based granular activated carbon General method Test operation Open the compressed air (or negative pressure suction) piston, use the piston (K1) to adjust the total air flow; use the piston (K2 and K3) adjust the humidity of the air flow; adjust the gas flow of the canister with the piston (K9). Slowly open the piston (K4) and the piston on the evaporator (or cylinder), adjust the liquid column height difference of the flow meter (K5) to the position where the concentration has been corrected in advance, and record the test time with a stopwatch. Determination method of mixed gas poisoning agent concentration: a. Gravimetric method: Weigh the weight of the evaporator before and after the test with a balance (accurate to 0.05g). The concentration of the mixed gas poisoning agent is calculated according to the formula (1): in the formula: c——Concentration of mixed gas poisoning agent, mg/L; m1——The weight of the evaporator before the test, g; m2——Weight of steamer after test, g; t——Evaporator opening time, min; V——Air flow, L/min. The chemical absorption method uses two absorption bottles to fill 25mL of absorption solution, and connect them to the DX-1 type device in series (see Figure 1). Open the piston (K6) and the mixed gas passes through the absorption bottle at a speed of 50~100mL/min, and measure the ventilation volume with a lower-mouth bottle and a graduated cylinder or a flowmeter. The gas volume through the absorption bottle for each test is between 1.5 and 3.0 L. At the end of the test, close the piston (K6), remove the absorption bottle, transfer the absorption liquid into the conical flask, measure the poisoning dose of the absorption liquid by chemical analysis, and calculate the concentration of the mixed gas poisoning agent vapor according to the volume of the water discharged from the lower mouth bottle. . Determination of Toxic Agent Vapor Permeation Canister——Indication method Put 20mL indicator solution in the indicator bottle, connect it to the DX-1 type test device (see Figure 1), and use 1.0±The speed of 0.1mL/min is passed through, and the test end point is judged according to the color change of the indicator when the trace poison penetrates the canister; it can also be measured by instrument. Close (K4) after the test, and continue to purge the instrument with clean air for 20min. Test results The poison concentration of each test should be effective within the specified range. The anti-virus time measured under the test concentration is converted into the anti-virus time under the standard concentration according to formula (2): where t——Antivirus time of the canister, min; t1——Antivirus time under test concentration, min; c1——Toxic agent concentration in mixed gas during the test, mg/L; c0——The specified standard concentration, mg/L. More related information: http://www.standard-groups.com/FilterMaterial/4.html
have manifold textile testing equipment effects, ranging from tensile tester manufacturers to tensile tester manufacturers.
GESTER International Co.,Limited is proud to be recognized as some of the most important and influential providers for global customers.Visit us at GESTER Instruments.
GESTER International Co.,Limited believes that the average profitability will be sufficient.
Our company specializes in manufacturing textile testing equipment mainly tensile tester manufacturers.
With the market analysts, exports from GESTER International Co.,Limited facilities in China will surpass the forecast.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Quick links