The measurement of the pilling performance of fabric by Martindale tester
1. Scope 1.1 This method is suitable for judging the ability of fabrics to resist pilling and other surface property changes. The instrument used is the Martindale testing-equipment' target='_blank'>tester, this method is suitable for all kinds of knitted fabrics and woven fabrics. 1.2 This method is not suitable for fabrics whose thickness exceeds 3mm (0.125in). 1.3 The samples can be washed or dry cleaned before testing. 2. Principle 2.1 Determine the pilling of the fabric and other related changes on its surface, such as using a test instrument to simulate the pilling that occurs during normal wear. Under slight pressure, the sample mounted on the sample holder and the fabric on the grinding table are rubbed against each other in a certain geometric pattern, and then the sample of the grinding table and the standard sample are compared and rated. 3. Equipment and standard materials 3.1 Martindale tester 3.2 Standard felt: gram weight 750±50g/m2 (22±1.5oz/yd2), thickness 3±0.3mm (0.12±0.01in). 3.3 Polyurethane foam, density 29-31kg/m3, thickness 3±0.01mm. 3.4 Grading box: cool white fluorescent lamp, bracket for placing test samples and standard grading sample photos. 3.5 Standard internal pilling detection cloth: According to the actual situation, save the fabric of known pilling level to check the performance of the instrument. 3.6 Sample photos for rating: A set of about 105mm wide, with the degree of pilling from 'very serious pilling' to 'no pilling 3.7 Sampler: Two kinds of diameter 38mm (1.5in) and 140mm (5.5in). 3.8 Washing equipment (if necessary) 3.9 Dry cleaning equipment (if necessary) 4. Sample preparation 4.1 Unless otherwise specified, the sample shall be washed or dry-cleaned before taking the sample. 4.2 Use two kinds of samplers to take 4 pieces of 140mm and 38mm samples from the samples to be tested. 4.3 The principles to be followed for sampling are: take samples immediately. If the samples are clothing, take samples at different locations; each sample does not contain the same yarn; do not take samples from wrinkled or woven locations; At a position that is more than 1/10 of the width of the entire fabric from the edge of the fabric. 4.4 The sample to be tested shall be kept for at least 4 hours under constant temperature and humidity conditions of 21±1℃ and 65±2%RH. 5. Test procedure 5.1 All test procedures must be completed under standard atmospheric conditions. 5.2 Place a piece of felt with a diameter of 140mm and a piece of specimen of 140mm on each grinding table in turn, flatten the specimen and felt with a heavy hammer (make sure there are no wrinkles, repeat the above process if it is not flat), and fix the ring. 5.3 Place the sample with a diameter of 38mm (1.5in) facing outwards and polyurethane foam in sequence on the sample holder. 5.4 Place the sample holder on the grinding table, insert the mandrel into the sample holder, that is, the test sample on the grinding table has a pressure of 3Kpa. 5.5 The counter needs to be adjusted to the zero position, preset to 100 revolutions, start the machine, and after 100 revolutions, the instrument stops automatically. 5.6 Place the ground sample in the grading box. 5.7 Compare the grading sample photos with the samples, and grade them by looking down at close to 45°. When the surface effect after grinding is between two levels, it can be rated as half level, such as 3.5 or 2.5. Note: 5-no pilling 4-slight pilling 3-medium pilling 2-severe pilling 1-very severe pilling as a reference, usually at least 2 individuals are required to grade separately. 5.8 Calculate the average of the rating results. 6. Report 6.1 The test method used is ASTM D 4970, describing the sample and sampling method. 6.2 The grade and average value of each test sample. 6.3 If the sample has been washed, the washing conditions shall be reported. 6.4 Number of runs. 6.5 Rating box type, the rating sample card used.
GESTER International Co.,Limited has famous reputation in worldwide.
GESTER International Co.,Limited will continue to bring our industry nuances of style and approaches to textile testing equipment which are consistent with our evolving aspirations.
When it comes to textile testing equipment tensile tester manufacturers, GESTER International Co.,Limited is the name to reckon with. Not only are they best, they are the most experienced as well and provide wide range of services as well as products at affordable prices. Find out more information on GESTER Instruments.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
Quick links
Products