Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
AATCC 135 fabric shrinkage test process and rating reference1
Scope of application: This test method is used for dimensional changes in woven and knitted fabrics after multiple home launderings.
Test principle: The dimensional change of the cloth box is calculated by the difference between the standard length delineated on the cloth box before washing in a representative household washing and drying process.
Test equipment: Wascator Automatic Shrinkage Tester For Fabric GT-D34 , Medicines: WOB washing powder 92g, total laundry weight: 1.8kg, weighted cloth: 92X2300px, white bleached cotton cloth, overlock. Sampling: Use the AATCC sampling ruler to cut the sample 50 X1250px, take 35 X875px (35 is the smallest, or it can be larger) on each side to mark three pairs, at least 3 samples. AATCC Shrinkage Washing Machine Technical Parameters: Standard: AATCC 88B, AATCC 88C, AATCC 124, AATCC 130, AATCC 135, AATCC 142, AATCC 143, AATCC 150, AATCC 159, AATCC 172, AATCC 179, AATCC 188
Test steps:
1) Sampling , Weighing, if it is less than 1.8kg, use a weighted cloth to make up.
2) Set the water level. Medium is generally used, and if the customer has special requirements, it will be based on the customer's requirements.
3) Set the water temperature. Generally washed with warm water and rinsed in cold water, or according to customer requirements. The water heater can adjust the water temperature.
4) Set the laundry program. Generally use Regular or according to customer requirements.
5) Take 92g of WOB washing powder, dissolve it in an appropriate amount of warm water and pour it into the washing machine.
6) Put the test sample and weighted cloth into the washing machine.
7) Start up and run, and take it out after the end.
8) Take out the test sample and weighting cloth and put it in the dryer.
9) Set the appropriate drying program and temperature, and start running.
10) After the operation, take out the test sample and weighted cloth, put it back into the washing machine, and carry out the experiment according to steps 2) to 9).
11) As mentioned above, carry out at least three cycles of washing and drying.
12) The dried samples are placed in the conditioning chamber for at least 4 hours, then the dimensional changes are measured and recorded. Test report: 1) Percentage of dimensional change in the length direction, take the average value of each measurement. 2) The percentage of dimensional change in the width direction, take the average value of each measurement. 3) Describe the laundry conditions used, including water level, water temperature, and washing program. 4) State the drying conditions used, including drying program and temperature. 5) Describe the change in appearance of the test sample after washing.
Wascator Automatic Shrinkage Tester For Fabric GT-D34
Automatic Wascator Shrinkage Tester Application
Wascator Automatic Shrinkage Tester accelerated washing apparatus for knitted and woven fabrics to assess shrinkage in accordance with international test methods. Also used for assessing fabric stability, color fastness, finish durability, spirality and pilling to washing.
Feature
1. Automatic Wascator Shrinkage Tester MCU program controller, build-in ten sets of washing program that ISO required, and operator program capability.
2. No need to fix to ground with foot screw, operating stably;
Soft link between rotating cage and rack, low vibration and noise;
Variable frequency motor, switch smoothly between high speed and low speed, low temperature increment of motor.
3. Blue fluorescence LCD display, test state dynamic icon shows, easier to catch the eye and operation convenience.
4. Non-touch capacitance water level meter to measure water level accuracy and reliable
Shrinkage Tester For Fabric Standards
GB/T8629, GB/T8630, ISO6330/5077, FZ/T70009, BS4923, EN25077/26330, JIS L1909, IWSTM31,ISO19954,
SATRA TM158
GESTER International Co.,Limited is recognized as one of the leading manufacturer of in China.Trust in us and make GESTER International Co.,Limited your textile testing equipment supplier. Our products will bring more economic value to you.
So, get ready to dazzle the world with Wascator Automatic Shrinkage Tester For Fabric GT-D34! Buy one today!! Visit GESTER International Co.,Limited at GESTER Instruments.
GESTER Instruments is one of the top brands in their class when it comes to textile testing equipment and tensile tester manufacturers. If you check online, GESTER Instruments is often rated high and reviewed with much praise. we would be very pleased to receive your inquiry.
GESTER International Co.,Limited can assure you that we never compromise on our quality standards and are one of the best in the market at present.
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
1. ISO 5402-1: Specifies the flexometer method for testing leather flex resistance under repeated bending.
2. ISO 17694: Defines test methods for footwear upper and lining flex resistance, simulating real-world bending stress to assess long-term durability.
C
Quick links