Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
Protective clothing hydrostatic pressure tester test principle and test steps
The protective clothing hydrostatic pressure testing-equipment' target='_blank'>tester is used to measure the liquid permeability and blood permeability of medical protective clothing, outdoor sports clothing, umbrellas, waterproof fabrics, jackets and other protective materials. Applicable standards: GB/T 4744, AATCC 127, ERT 120-1 160-0, BS EN20811/3321/3424, AFNOR G07-057, ISO 811, JIS L1092A, JIS L1092.B-a, JIS L1092 B-b, ASTM F903C, ASTM F1670, ASTM F1671, EN 1734, ISO 1420, FZ/T 01004. Main parameters: 1. Test pressure: 0-5000mbar (5000cmW.G); 2. Pressure accuracy: resolution 0.1mbar; 3. Test area: 100cm2 (optional 10cm2, 19.63cm2, 26cm2, 28cm2); 4. Sample thickness : no more than 40mm; 5. Compressed air: 6-8bar (clean and dry air); 6. Alarm time: 0-9,999min (can be set according to pressure or time). Test principle: The sample is fixed on the test area of the standard area, and the air compressor adds 0-5bar air into a water tank filled with distilled water, and applies a certain pressure of water to the sample. Testing can be done either dynamically or statically. (1) Dynamic method: The hydrostatic pressure resistance performance of the sample is determined by testing the pressure when a fixed number of water droplets seep out from the side of the sample that is not in contact with water at a certain pressure increase rate. (2) Static method: The hydrostatic pressure resistance performance of the material is determined by testing the water seepage of the sample after maintaining the pressure for a certain period of time under a certain hydrostatic pressure. Test steps: 1. Cut the test fabric into 100mm×100mm size sample; 2. Put the sample into the fixture, tighten the fixture to fix it well; 3. Press the up button, the metal container containing 700ml of water starts to rise at a constant speed under the drive of the motor, and the sample in the fixture starts to rise at a constant speed. Increase the water pressure; 4. Measure the water penetration by observing the color change of the indicator paper covering the filter paper sample through the plastic window of the clamp; 5. When the initial signal of the indicator paper color change (from blue to pink) appears, Immediately read the water level height of the ruler, expressed in Pa (mmH20); 6. Press the up button again to stop the metal container from rising, and record the reading as the test data of the impermeability of the filter paper; 7. Open the fixture, take out the sample and the indicator paper, Dry the load window of the fixture with a soft cloth, and check the water level in the fixture; 8. If necessary, refill the water, place another sample and indicator paper on the fixture, and repeat the above test steps to test.
GESTER International Co.,Limited thinks that customer satisfaction is one of the most important determinants of brand loyalty. High-quality service can be the difference between a one-time buyer and a lifelong repeat customer.
GESTER Instruments is also committed to maintaining excellence, respect, and integrity in all aspects of our operations and our professional and business conduct.
Like anything else in tensile tester manufacturers, there are a variety of choices and types to choose from, and each of them will affect your budget in some form. GESTER International Co.,Limited offers a range of quality at competitive prices.
For GESTER International Co.,Limited as a whole to adopt an attitude of acceptance toward change and technological innovation, we first have to truly embrace it and practice what they preach. Technological development needs to be more than just another investment, but a complete integration.
If something seems too good to be true, then it can be a , which provides tensile tester manufacturers value over its cost.
Ball Burst Method (ASTM D3787): Steel ball penetration for textiles/films using testers like GT-C02-2.
Hydraulic Method (ISO 13938.1): Fluid pressure on rubber diaphragm for industrial fabrics via GT-C12A.
Pneumatic Method (ISO 13938.2): Compressed air for breathable materials tested with GT-C12B.
Results are influenced by raw materials, yarn properties,
Quick links