Gester Instruments | Professional Textile, Footwear and PPE Testing Equipments Manufacturers Since 1997
Analysis of test steps of automobile interior combustion tester
The car interior combustion testing-equipment' target='_blank'>tester adopts the horizontal direction burning performance test method, which is used to measure the relative burning rate and flame retardant performance of various textile fabrics, clothing, tents, especially automobile interior decoration fabrics. (Hong Kong) Co., Ltd. is the manufacturer, welcome Inquiries from customers in need. Applicable standards: GB 8410, ISO 3795, FMVSS 302, DIN 75200, SAE J369, ASTM D5132, JIS D 1201, AU 169. Main parameters: 1. Flame time: 0-999.9s±0.1s adjustable; 2. Delay time: 0-99h59m59.99s±0.1s; 3. Test wind speed: between 0.10m/s ~ 0.30m/s; 4. Test gas: liquefied gas or other combustible gas (such as natural gas, city gas) of 35MJ/m3~38MJ/m3. Test steps: 1. Adjust the test environment with a temperature of 10°C to 30°C and a relative humidity of 15% to 80%. 2. The sample is at least 20mm away from the frame, and the sample holder is installed on the top bracket of the combustion box to ensure that the sample is vertical. 3. Place the marking line horizontally in front of the sample pressing plate. The distance between the marking line and the surface of the sample is 1mm and 5mm respectively, and the marking line should maintain sufficient tension. 4. Light the gas lamp and adjust the flame height to 40mm±2mm, adjust the placement angle of the gas lamp, 30 degrees from the plane where the sample is located°angle. 5. The sample is ignited in the flame of the gas lamp for 5s, immediately extinguish the gas lamp and reset it. 6. If the sample does not burn, it is considered not ignited, and another pretreated sample needs to be re-tested, but the ignition time of the sample in the flame of the gas lamp is 15s. 7. If any one of the three samples in any group exceeds 50% of the minimum value, another group of samples in the same direction should be taken for the test again. If one or two specimens in any group of three specimens do not burn to the third marking line, take another group of three specimens in the same direction and perform the test again. 8. Measure the following times, in seconds (s): a) Time t1 from the start of ignition to burnout of the first marker line; b) Time t2 from the start of ignition to burnout of the second marker line; c) From the start of ignition It is time t3 when the flame burns the three-marked line. 9. Calculation For the sample whose combustion flame reaches at least the first marking line, the combustion speed (Vi) is calculated as follows: Vi=60×(Di/ti) where: Vi——Burning speed, in millimeters per minute (mm/min); i——The flame burns to the one/two/three mark lines, 1, 2, and 3; Di——The burning distance of the flame to the one/two/three mark line, the unit is millimeter (mm); ti——The burning time for the flame to burn the 1/2/3 marker line, the unit is seconds (s). The burning velocity of each sample shall be the larger value of V1, V2 and V3. The burning velocity of a group of samples shall be the test result of the burning velocity of three or more samples, and the calculation result shall be rounded to an integer.
In today's world, have risen to an unexpected level of tensile tester manufacturers. It has gained a lot of popularity and has come up with different kinds of variations in its content.
To know more about and the market trends, go to GESTER Instruments.
GESTER International Co.,Limited, a manufacturer of textile testing equipment, might emphasize less hassle or less wasted time rather than emphasizing reliability or quality.
GESTER Instruments clearly and succinctly expresses what our company is all about. Strong brands cut through the noise to grab the audience and immediately shed light on the character of the product or service.
textile testing equipment is one of the best products sold in the market today.
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
1. ISO 5402-1: Specifies the flexometer method for testing leather flex resistance under repeated bending.
2. ISO 17694: Defines test methods for footwear upper and lining flex resistance, simulating real-world bending stress to assess long-term durability.
C
Quick links