Precautions for washing color fastness test
Washing or soaping fastness refers to the degree of color change of dyed fabrics after washing with washing liquid. The gray graded sample card is usually used as the evaluation standard, that is, the color difference between the original sample and the faded sample is used for judgment. The washing fastness is divided into 5 grades, grade 5 is the best and grade 1 is the worst. The fabrics with poor washing fastness should be dry-cleaned. If they are wet-washed, the washing conditions should be paid extra attention, such as the washing temperature should not be too high and the washing time should not be too long. So, what matters should be paid attention to when doing washing color fastness test? 1. Determine the type of fabric to be produced. Carry out a careful analysis of the samples from the customer, determine the type of cloth used in the production of bulk goods, cut each piece of cloth together and sew together, mark it, and require a trial wash based on the washing water, and also the shrinkage of the trial cloth. For ready-to-wear denim sent by the garment factory to be washed, the goods must be inspected to see if there are stains, holes, cloth defects, pinholes, lathes, and excessive thread ends. 2, pilot test/test cylinder. In order to finally decide on the mass product formula, usually 50 samples are washed in the pilot test. After the department confirms that it is correct, the back-end inspector will check it again. The mass product can only be produced when the genuine product rate reaches 98%. If there is any problem, report to the relevant department in time. 3. Produce bulk goods. Because the washing tank volume and bath ratio used for washing samples and goods are different, the color of the cloth will be different, so the washing water formula must be revised. The same batch of goods must be washed in a tank and dried and all checked, and then washed after there is no problem. One tank, the cycle is carried out, and it is never allowed to dry and inspect after all washing is completed. If there is any problem, analyze and deal with the problem on the spot, and report to the relevant department in time. 4. Make a board/test a sample. Wash samples in the plate washer/plate vat according to the customer's requirements. For any type, 10 samples must be sampled first. After drying, they will be approved by the department and then confirmed by the company's corresponding documentary personnel. After the authenticity rate reaches 100%, the sample can be carried out. If there is a problem, it can be improved in time. During the trial wash process, each wash formula parameter that was changed should be kept, and the cloth samples before wash should be archived.
In the past few decades, tensile tester manufacturers production has increased because of the use of textile testing equipment.
With continuous operational improvements, expanding capacity and a strong competitive position for serving strategic domestic markets, GESTER International Co.,Limited are positioned for long-term growth that will benefit our customers and investors.
tensile tester manufacturers needs not be tedious anymore with the application of . So getting the right textile testing equipment can drastically promote tensile tester manufacturers.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Cut resistance is one of the most critical performance indicators in personal protective equipment (PPE) testing, directly affecting worker safety in high-risk industries such as metal processing, machinery manufacturing, and emergency rescue. The TDM Cut Test Machine GT-KC28 plays a vital role in accurately evaluating the cut resistance of PPE products, including gloves, protective clothing, footwear materials, composite materials, rubber, and industrial textiles.
By adopting high-precision force control systems, intelligent data processing, and stable transmission technology, the GT-KC28 TDM Cut Tester can accurately measure the critical cutting force of materials and ensure excellent repeatability and comparability of test results. Its user-friendly touch-screen operation, comprehensive data storage, USB data export, and built-in thermal printer greatly improve laboratory efficiency and data traceability.
The TDM Cut Test Machine GT-KC28 fully complies with major international and national standards such as ISO 13997, EN 388, ASTM F2992/F2992M, ANSI/ISEA 105, and GB 24541-2022, making it a reliable solution for PPE manufacturers, third-party testing laboratories, and research institutions. Through precise and standardized cut resistance testing, the GT-KC28 helps reduce industrial cutting injuries, supports PPE certification across global markets, and ensures that protective equipment delivers reliable safety performance in real-world applications.
Quick links
Products